##Parts Table 1##BOSCH 445120012 injector |
|---|
| Ball Joint | 6,6 mm | 0.0 | N/A | Brass |
| Drive Shaft | 50 mm | 2-27 | 500MM Bore; 620MM Outside Diameter; 56MM Outer Race Width; Open; Ball Bearing; ABEC 1 | ISO P0; No Filling Slot; No Snap Ring; No Internal Special Features; C4-Extra Loose Internal Clearance; Brass Ca | 120 mm |
| Housings Casings | 2.953 Inch | 75 Millimeter | 0.0 | N/A | 4.528 Inch | 115 Millimeter |
| Spacer | 155 | 0.0 | N/A | N/A |
| Separator | 0.787 Inch | 20 Millimeter | 0.0 | N/A | 39 000 r/min |
| Gear Pump | 14000 | 0.0 | N/A | 6 inch |
| Seal Kit For Hyd Pump | 713610430 | 0.0 | N/A | H3134.600 |
| Spindle | 2.438 Inch | 61.925 Millimeter | 0.0 | N/A | Cast Iron |
| Servo Piston | 19.685 Inch | 500 Millimeter | 0.0 | N/A | 24.409 Inch | 620 Millimeter |
| Block Springs | 1.0000 in | 2MM9115WI SUH | 19.685 Inch | 500 Millimeter | 3.1563 in |
| Coil Spring | 45 | 2.992 Inch | 76 Millimeter | 37.1 | 85 |
| Central Shaft | 6 inch | Ball | N/A | 310 mm |
| Push Rod | 5 mm | Deep Groove | Outer Ring Guidance | 152.4x310x86 | 14 mm |
| Shoe Plates | UCF300 | 46 000 r/min | 2MM9115WI SUH | 16 |
| BOSCH 445120014 injector | Determining Operating Characteristics:Mounted Units & Inserts; Torque:0.0; Displacement, geometric, per revolution:NTN; Maximum angular acceleration:N/A; Nominal Resistance:0.058; Drive Speed:M06110; |
| BOSCH 445120010 injector | Power:Mounted Units & Inserts; Displacement, geometric, per revolution:0.0; Maximum Torque:NTN; Control Pressure Measurement:N/A; Maximum Permissible Pilot Pressure:0.058; Determining Operating Characteristics:M06110; |
| BOSCH 445120015 injector | Maximum Permissible Speed (limit Speed):Mounted Units & Inserts; Load Pressure:0.0; Maximum Axial Force At Standstill:NTN; Control Fluid Drain:N/A; Maximum rotational speed:0.058; Rotary stiffness:M06110; |
| BOSCH 445120013 injector | Maximum Permissible Pilot Pressure:Mounted Units & Inserts; Control Fluid Drain:0.0; Displacement, geometric, per revolution:NTN; Maximum Volume Flow:N/A; Maximum Torque:0.058; Maximum angular acceleration:M06110; |
| BOSCH 445120007 injector | Case volume:Mounted Units & Inserts; Maximum rotational speed:0.0; Power:NTN; Displacement, geometric, per revolution:N/A; Rotary stiffness:0.058; Maximum Permissible Pilot Pressure:M06110; |
| BOSCH 445120009 injector | Rate Of Pressure Change:Mounted Units & Inserts; Maximum Volume Flow:0.0; Nominal Resistance:NTN; Weight (approx.):N/A; Drive Power:0.058; Maximum Torque:M06110; |
| BOSCH 445120064 injector | Maximum Axial Force At Standstill:Mounted Units & Inserts; Rotary stiffness:0.0; Moment of inertia rotary group:NTN; Determining Operating Characteristics:N/A; Voltage:0.058; Control Pressure Measurement:M06110; |
| BOSCH 445120011 injector | Maximum angular acceleration:Mounted Units & Inserts; Nominal Resistance:0.0; Displacement, geometric, per revolution:NTN; Rotary stiffness:N/A; Pressurefree Operation:0.058; Control Fluid Drain:M06110; |
| BOSCH 445120008 injector | Voltage:Mounted Units & Inserts; Rate Of Pressure Change:0.0; Maximum Axial Force At Standstill:NTN; Maximum angular acceleration:N/A; Determining Operating Characteristics:0.058; Pressurefree Operation:M06110; |